How To Connect Wire To Socket And Switch

How To Connect Wire To Socket And Switch – British Plug, Type G Plug or BS1363 Standard Plug by IEC = International Electrotechnical Commission) also known as three-pin plug used to power electrical appliances and equipment. There are several types of three-pin plugs, e.g. Type A, B, C, D, E, F, G, H, I, J, K, L etc. but G 3 type pin plug is more popular in United Kingdom, Singapore, Hong Kong, Malta, Malaysia, Ireland, Cyprus. , Qatar, Oman, Kuwait, KSA, United Arab Emirates, Israel and other countries that fully or partially comply with IEC regulations.

There are three terminals and a fuse (the rating is different depending on the requirements of the load circuit) inside the UK three pin electrical plug as follows:

How To Connect Wire To Socket And Switch

The live terminal should be connected to the brown wire (from the cable). It will carry the voltage (and current) from the source to the load point. A live terminal is also called a Fire, Line or Phase terminal. The straight end screw is electrically connected to the input of the safety fuse and the output of the fuse is connected to the straight pin.

The 5 Essential Outlet Tests Every Homeowner Should Know How To Do

The neutral terminal should be connected to the blue wire. The neutral wire provides a return path for current when the circuit is complete.

The ground terminal is long and narrow for security reasons. For this reason, the green wire with the yellow ground line should be connected to the ground terminal.

A standard fuse (usually 13A) is built into the BS1363 plug. The rating of a ceramic fuse in a UK plug can vary as it depends on the current capacity and the types of load being protected. The main function of the fuse in the UK plug is to protect the electrical cord, the device connected to the cables and wires in case of overheating, overload and overcurrent.

For example, a 13A fuse with a voltage of 230V, 50Hz of a household supply is equivalent to approximately 3000 watts (3kW). If the load current exceeds the fuse rating limit (in the event of a fault, for example, a short circuit) it will trip or trip the RCD/MCB circuit breaker in the main consumer unit.

How To Install An Electrical Outlet Receptacle

Good to know: The fuse in the three-pin power plug must be rated to BS1363 standards. For example, if a lower power unit (1100W or 700W) is used instead of the previous higher power unit (2.5-3kW with a 13 Ampere fuse in the power outlet), the fuse rating must be reduced according to its current capacity. behavior , e.g. 3A for 700W and 5A for 1100W devices.

Cable clamps are used to prevent cable stretching during normal operation and to pull the wire from the screw terminals. Cable clamps or strain relief should be firmly attached around the cable after connecting the lead wires to the correct terminals.

Good to know: The BS-1363 aka British plug is the safest plug in the world for the following reasons.

We have used the following IEC cable color codes for the single 230V supply voltage used in the UK and EU. The old UK wire color codes (before April 2004) are also mentioned below.

Leviton 3 Way Socket Lamp Holder R50 07090 0pg

All information about electrical and electronic engineering and technology. Follow Electric Technology on Facebook, Twitter, Instagram, Pinterest, YouTube and Linkedin for the latest updates or subscribe to have the latest technology articles delivered to your inbox.

Our website is able to display online advertisements to our visitors. Please consider supporting us by turning off the ad proxy. We rely on advertising revenue to continue creating great content for you to learn and enjoy for free. The Stack Home Improvement Marketplace is a question and answer site for serious contractors and hobbyists. It only takes a minute to sign up.

I am trying to install a dimmer switch in the living room. I have two pendants that are controlled by one wall socket and two switches for each light. My property is a new build and is located in England.

So much for thinking this would be as easy as cutting the wires and plugging them into the same sockets on the new dimmer switch!

Make Your Own Extension Board

This seems more complicated than a few strings to change. It looks like there are some wires coming out of the wall. The green/yellow earth is loose on the back plate and the plastic end cap.

The wire in L1 and Com is removed on the first switch towards the end of the wire, the stripped part is on the L1 or Com connector, and then the end of the wire is kind of plugged into the other L1 or Com connector. another switch.

. I tried to copy the wires but when the wires were in the original sockets in the N ports (loop) I put them in L2 in the new socket as that was the only other unused port.

It appears that the old switch has Com, N (Loop), L1 and L2 ports, but the new dimmer switch only has L1, L2 and Com.

Home A/v Connections Glossary

I tried this setup and it worked as the lights were on and the lights were dimming (even though they were dimming, probably bad power bulbs) but when I tried them to turn it off they blew a fuse in the main fuse box.

As you can tell, I don’t know anything about wiring or anything like that. Any help or pointers anyone can give me would be greatly appreciated.

I was wondering if I have the wrong type of light switch, but I can’t find any other type.

I’ve also included a picture of the instructions, although they don’t make much sense to me and don’t exactly match the original wiring of the original connector.

How And Where To Properly Install Pc Cables And Wires For Ssd, Panel Switches, And More

All sorted now, basically I have a plastic box on the back but the tires have contacts on them. The Loop N terminals are simple, so I bought a terminal block to connect them together. Just wire L1 and Coms the same as the new dimmer switch. I haven’t done it yet but I got my answer from another forum.

By clicking “Accept all cookies”, you agree that Stack Exchange may store cookies on your device and provide information in accordance with our Cookie Policy. The BS1363 (and IEC) socket is also known as an RA socket or Type G socket. It has several types namely 1 Gang, 2 Gang and then three pins with or without switches and neon bulbs. It is also available in different shapes / designs and the wiring depends on the system requirements and yes, we will discuss directly in the upcoming posts.

Three Pin sockets are one of the most popular and widely used sockets and plugs in various countries such as UK, EU and other Arab and Asian countries due to the following reasons.

In the following wiring guide, we’ll show you how to wire a new (or outdated) switch. Two switches can be used to control the ON/OFF operation of each outlet. The neon bulb indicates the ON and OFF position of the switch, that is, if the bulb is ON, the switch is ON and the circuit is working and vice versa. The advantage of the red bulb in the switch is that the neon light can be easily seen in dark areas indicating that the device is connected Off or ON.

Farfi Car Aux Usb Socket Switch With Cable For Bmw E60 E61 E63 E64 E87 E90 E70 F25

We have used the following IEC cable color codes for the single phase 230V supply voltage used in the UK and EU. The UK used its own wire color codes before April 2004, and some countries still follow the same old wire color code as the UK. The UK now follows the IEC wire color codes.

2-Gang 3-Pin Socket UK Socket BS1363 Double Replacement Socket 2-Gang Twin Socket Type G UK Socket

All information about electrical and electronic engineering and technology. Follow Electric Technology on Facebook, Twitter, Instagram, Pinterest, YouTube and Linkedin for the latest updates or subscribe to have the latest technology articles delivered to your inbox.

Our website is able to display online advertisements to our visitors. Please consider supporting us by turning off the ad proxy. We rely on advertising revenue to continue creating great content for you to learn and enjoy for free.

How To Wire A Light Bulb Holder

How to wire outdoor socket, how to connect speaker wire, how to wire ethernet socket, how to wire a light socket ceiling, how to wire plug socket, how to connect switch and socket, how to wire a light bulb socket, how to wire light socket, how to connect electrical wire, how to connect telephone wire to socket, how to wire an electrical socket, how to connect wire to light bulb socket

Leave a Comment