en'>

How To Make A Butcher Block Table

How To Make A Butcher Block Table – Some of my friends just moved into a new apartment and I wanted to make something as a housewarming gift. Their new kitchen is small and doesn’t have much space to prepare food, so I decided to make it a kitchen island. I looked for plans on the internet, but it quickly became clear that due to the many limitations of this island, I would have to build my own island. This is how I designed and built the island.

To fit in my friends kitchen, the top of the island had to be 4 feet by 18 inches, so I built it to those measurements. I found that a standard island height is about 36 inches and the top of the island should be about 1 inch on all sides.

How To Make A Butcher Block Table

How To Make A Butcher Block Table

I figured the top of the block piece would be about 1-1.5 inches thick, so the legs (shown in the light) would be 34.5-35 inches long. The height of the shelf doesn’t really matter so I made it 35 inches and kept it regardless of the thickness of the shelf. I bought a 4×4 for four legs, but the big legs are fine. The front of the shelf looked thin, so I decided I needed to cut it down to 2.5 x 2.5″. The other part of the legs I wanted to add was to cut them to match the pieces. long shelves (you can see the pictures. for a better understanding). I started 2.5″ and 17.5″ from the bottom of the legs so that the shelves are the same height.

How To Cut, Seal And Install Butcher Block Countertops

For the support shelves (shown in pink), I made 1.25″ x 2.5″ to match the size of the legs. All of these large changes require 4×4’s and 2×4’s to be ripped to a smaller cross section, a pain but worth it to get the final product to the correct size. According to the general measurements I talked about above, I made 4 long pieces 46 inches long and 4 short pieces 11 inches long.

How To Make A Butcher Block Table

Finally, I decided I needed a way to attach the top of the island, so I added some screws and bolts that I could use to screw the top in (shown in the green). For short long pieces, just cut 1×3 (actually 0.75×2.5 inches). The long pieces are 41 inches long and the short pieces are 11 inches long. The cross pieces that run down the top of the island are about 14.5 inches long. Their size is not very important, because it is only intended to improve the surface.

For the sheets (shown in yellow) I made a small table of different width panels with 1/2″ or 3/4″ gaps that I could hold firmly on each shelf and get the right size to fit. the shelf. I found that 11 strips, 3.5″ wide and .75″ apart, were the perfect size to fit each shelf. Since everything was a nice round number, it was easier to cut and fit each space to fit the shelves.

How To Make A Butcher Block Table

Butcher Block Kitchen Islands

Instead of trying to make a butcher block out of scratch, a friend of mine had an old lab bench that he didn’t use for anything, so he let me use it. As you can see from the pictures it was pretty banged up so it needs a lot of work. The first part of the lab is 6 feet long by 2 feet wide and I need a 4 foot x 18 inch island top. I attached a piece of wood to the butcher block as a straight edge and cut the piece from top to bottom with a circular saw. in measure. I then used a random orbital sander to remove the current finish and remove any nicks and scratches. I rounded all the corners by running the sander over each edge. Maybe a router would give you a more consistent edge, but I didn’t have one, so I worked with what I had. Doing all of these things really helped to clean up the top and bring out the beautiful wood as you can see in the picture. To protect the top, I used a block seal that contains both mineral oil and some type of grease to prevent drying and cracking. no, it also affected the beautiful rich color of the top.

I bought 4x4s for the legs, but they seemed too big and awkward for the size of the island I wanted to build, so I decided to make it smaller. I used a table saw to cut each leg 2.5″ on each side, then measured the 4 legs at 2.5″ x 2.5″ x 35″. After it was ripped, I had to sand all the sides to smooth out all the cut marks and round the corners. I also designed the legs to have cutouts for the long shelf supports that are 2.5″ x 1.25″. To cut the legs, I first drew lines on the legs where I wanted to place the points and set the table cutting depth to match the thickness of the cross pieces 1.25 inches. From here I just put my foot in the cross on my cutting table and cut again until I remove everything from the stage. It’s a good idea to use a test piece to make sure the cuts are the correct depth.

How To Make A Butcher Block Table

The shelf supports were made in the form of legs. I cut the 2x4s to 1.25×2.5 inches and cut them to length. For this step, I need 4 long shelf supports 1.25″ x 2.5″ x 46″ long and 4 short supports 1.25″ x 2.5″ x 11″ long. I repainted all four sides and corners to make sure everything was even. For the longer pieces, I stitched and screwed from the back leg to the wall shelf, and attached the shorter pieces with pocket staples. After attaching these parts to the legs, you can make sure that your legs are straight and will not move and adjust before you go anywhere else.

Reclaimed Wood Butcher Block Island

Cutting the pieces is easier because you just cut them lengthwise. There should be 4 units of 1×3 (0.75″ x 2.5″ or you can use 1×4, it doesn’t really matter). These two pieces should be 41 inches long and two of these pieces should be 11 inches long. When I used it I made sure that it was absorbed in the parts of my legs and lined up with the outer edges as you can see in the picture. After attaching them to the pocket square markers, I cut the cross pieces to fit in the middle. Their position does not matter if they float on the top of the legs and decorate where the top of the island will be.

How To Make A Butcher Block Table

The surface of the cinder block can expand and contract due to heat and moisture, so you must allow the cinder block to move when installing. To do this, I drilled 3/8″ holes in the cross pieces (a larger hole than my screws needed) and then used a 1″ overhang on the nails to allow them to move.

For the shelves, I bought some 1x8x24″ strips from Home Depot for about 36 cents (when I saw how cheap, I bought a whole supply). I was able to tear them to the width I needed and cut to length to make 2 of these shelf boards each 0.75″ x 3.5″ x 16″ long and I needed 22 boards to cover both shelves. I had to cut off some of the back pieces on each side to fit around the legs. To do this, I simply measured and marked 4 slats and cut them with a hand saw. I used a double blade pull saw ( like this one ) which made some nice cuts. Since I planned to have an exact 0.75 inch gap between the sheets, I used two small pieces of material to make the space between the sheets and glued them together at a time.

How To Make A Butcher Block Table

Solid Wood Butcher Block Table

Once this is done, your wood is done! The last step is to paint or stain the legs and pieces of paper to your liking. I’ll update when it’s done, but for now, please vote for me in the contest! We moved into one in the early 1990s (when Ryan and Emmy were young).

How to clean butcher block table, how to make butcher block countertop waterproof, how to make butcher block countertop, how to build a butcher block table, how to make a butcher block island, butcher block how to, how to make butcher block counter top, how to finish a butcher block table, how to make butcher block table top, butcher block how to make, how to refinish a butcher block table, how to make a butcher block table

Leave a Comment