How To Make An Ironing Board Cover For Quilting – Wife, mother and lover. Coffee lover and endless project starter. A kindergarten teacher became a stay-at-home mother.
Today I went to get the iron plate and noticed that it looked a bit messy. I have this iron plate. The packaging is thin and easily coated with wool glue. The point is that it’s bad!
How To Make An Ironing Board Cover For Quilting
I have a wider iron plate, so it’s not always easy to find covers in stores, and the ones online are cute and a little more expensive. Luckily I had everything I needed on hand so it was a quick job. If you want to cover yourself, you will need:
How To Re Cover Your Ironing Board The Easy Way
I had an old curtain panel that I wasn’t going to use in our new house, and this was the largest size I could cover the iron panel. To start, I removed the old ugly tin cover and spread the first layer of putty (thick) on the floor. A minor is optional.
Then I cut the batting around the iron plate, leaving about 3 inches all around. I just noted it, but you can measure it and mark it with a pen or pencil if you want. I have a little extra on the board for the iron, so I stopped when I got to that part, moved the board to the side and cut it straight, still having about three inches left.
Then I laid the cotton bat on the floor and molded the top of the cut thick bat. Additional ball fights are completely optional. I knew I needed a lot of padding under the cover because I use the ironing board a lot, and I had a cotton bat on hand.
Ironing Board Cover Elasticated Easy Fit Double Layer Heat Reflective Backing
Finally, I laid the fabric on the floor (wrong side) and used the distance as a guide. Again, I closed my eyes and turned around and filled up, staying around 4-5.
So it’s time to sew the piping to the rubber. Starting at one end, I folded the end twice and pinned it in place. The bend was a bit tricky so I had to overlap the edges one by one. As long as you have enough room to feed the rubber, you can roll the ends a little because you won’t be able to see that part once it’s opened.
So it’s time to sew! I sewed as close to the edge as possible, leaving about 2 inches (5 cm) to insert the elastic.
How To Make An Ironing Board Cover Tutorial
I then tied a safety cap to one end of the rubber and threaded it through the tube. It took time, and I had to slow down and tear the fabric as I built it. Once you’ve gone through this process, try to loosen the fabric so that there is some flexibility at both ends. Be careful not to move the end of the hose without the safety box. (Maybe I know this from experience.)
So it’s time to put it all together! I placed a layer of batting on top of the iron plate, then carefully placed the top over it, carefully sliding it between the plate and the iron rest. After I got it in place, I confirmed where the installation was, and the cover looked around. Finally I tied the ends of the elastic tightly and tucked the ends under the cover.
After I finished the binding and saw how easy it was, I couldn’t believe I hadn’t done it sooner! Now I have a clean and well packed iron plate. Let me know if you decide to make your own.
Diy Plastic Free Ironing Board Cover And Natural Wool Pad » My Plastic Free Life
Hi, I’m Megan, Creative Minds Made by Megan. I hope you get some inspiration while you’re here. This post is embarrassingly long in the making because my ironing board has been in desperate need of a new cover for longer than I care to admit. I don’t know why I waited so long because it took me less than an hour to make a new one (which includes all the pictures in the tutorial!).
I would buy a new cover for the ironing board, but everything I saw in the store was ugly and cheap. They are usually made with only one layer of filling and often do not stay in place. Even though what I had was too thin, I liked the design so I made a new and better ironing board cover based on the old one! Bonus, I used a fabric that looks great on my dresser.
This post may contain affiliate links, which means that while I don’t get paid to promote certain items, I do earn a small amount if you buy something through those links. For more information, visit my website
Diy Ironing Board Cover: Sewing Tutorial
To start, I removed all the rubber from the old iron plate cover and set it aside. I then smoothed out my old cover as much as possible so I could use it as a model. I attached it to felt and cut it. There is no need to add an additional allowance. If you don’t have a cover to paint on now, place your iron board template on top of the canvas, adding two inches to each side.
This is my favorite part of the old cover. There is a dimple in the pointed end that fits the edge of the board. This socket really helps my cover stay up, so I wanted to copy it. I used an allowance piece to cut and trace this piece, but you could easily draw a similar piece using the image below as a guide. Follow the edge of the large piece of cardboard you cut out and make an arch under it.
Next, pattern the already cut cover with two pieces of cotton batting (only one layer is fine if you are using Insulin-Brit). Place the end of your insert, right side up, and clip around it. So now you have a sandwich with two pieces of stuffing on the bottom, then your top piece, then your final piece, on the right side (without the right side of the fabric).
Sew An Easy Diy Ironing Board Cover
Glue everything together, or if you don’t want to be fancy, you can use double-sided tape in the next step to create a curve along the edge.
Sew double-sided tape around the binding and the curved edges (see next photo). So double-sided tape is
Go to the pointed end of the sleeve as it turns inside out. Hope that makes sense! Wrap the raw edge around the double-sided tape and sew along the edge of the double-sided tape, making sure to catch the opposite side as well. If you are new, this may take some practice. Instead of wrapping the ends of the single-sided tape around as you go around, push them together so you have an opening for your elastic. Once you’ve used the single-sided video, you can turn the socket right side out.
Diy Ironing Board Cover
Finally, thread the rubber through the double-sided tape. If you are reusing rubber from an old shell, you don’t need to set it. If not, try ironing the cover and adjusting the elastic before tying or sewing the ends.
That’s it! Place the new cover over your iron plate, socket end first. I’m so glad I finally took the time to restore my ironing board! It looks great. My nails look so bad that if I have to take pictures of them being ironed for a blog post, I’m going to cover them with a hard cloth, ugh! I’m glad I don’t have to do that anymore.
Usually, when I go to the fabric store, I know exactly where to go and what thread and color to look for, without thinking about choosing another four-part sewing thread, which I usually don’t. Don’t even take a second look.
Ironing Board Cover
I’m so excited to reissue the printable sew-on comic gift tags with a more festive color scheme! All of these tags are only $4 and are super quick and easy to print and use.
If you are a handy person who likes to make something with your hands, you might want to give it a try
Ironing board cover for quilting, ironing pad for quilting, extra wide ironing board for quilting, portable ironing board for quilting, wool ironing mats for quilting, best ironing board for quilting, wool ironing pad for quilting, ironing mat for quilting, how to make ironing board for quilting, how to make an ironing pad for quilting, ironing board for quilting, quilting ironing board
